User manual Fetco Home Decor Water Dispenser HWB-2000

If you found this page, you probably have a problem and you need a user manual for the device Fetco Home Decor Water Dispenser HWB-2000. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Fetco Home Decor Water Dispenser HWB-2000 it belongs to the category Water Dispenser. A user manualFetco Home Decor Water Dispenser HWB-2000 is taken from the manufacturer, a Fetco Home Decor company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Fetco Home Decor Water Dispenser HWB-2000 directly. You can view the user manualFetco Home Decor Water Dispenser HWB-2000 directly online or save and store it on your computer.

HWB-2000 Series  
Hot Water Dispensers  
FOOD EQUIPMENT TECHNOLOGIES COMPANY  
6
40 Heathrow Drive Lincolnshire IL 60069 USA  
3
Phone: (800) 338-2699 (847) 719-3000 Fax: (847) 821-1178  
E-mail: techsupport@fetco.com Internet: http://www.fetco.com  
Installation  
For Qualified Service Technicians Only)  
(
Keys To A Successful Installation  
Electrical: All FETCO dispensers require NEUTRAL. Ground is not an acceptable substitute. Installation  
without neutral may cause damage to the electronic components.  
The power connection to L1 on the terminal block must be at least 105 volts. Less than 105 volts will cause  
erratic behavior.  
The power switch has a built-in circuit breaker. To reset it, turn to the “off” position, and then back to the “on”  
position.  
The wiring diagram for the dispenser is located on the inside of the cover.  
Plumbing: This equipment is to be installed to comply with the applicable federal, state, or local plumbing codes.  
The water line must be flushed thoroughly prior to connecting it to the dispenser to prevent debris from  
contaminating the machine. An in-line water filter is strongly recommended.  
Verify that the water line will provide at least 2 gallons per minute before connecting it to the dispenser.  
General: Utilize a qualified beverage equipment service technician for installation.  
Do not adjust the thermostat settings unless absolutely necessary. They are set at the factory for optimum  
performance.  
Installation Check List  
The installation must comply with applicable federal, state, and local codes having jurisdiction at your location. Check  
with your local inspectors to determine what codes will apply to the installation and operation of FETCO products.  
1
.
.
Verify that the actual voltage at the electrical service connection is compatible with the specifications on the  
dispenser’s serial number plate. Make sure the electrical service includes neutral. Ensure at this time that the  
circuit breaker to the dispenser and the power switch on the dispenser are in the off position  
The temperature and the water tank fill level are pre-set at the factory. There is no need to turn off the heaters  
during the installation process. The heaters are disabled by the liquid level control board until water is sensed.  
The heating process will start automatically when the tank has filled with water  
2
3
4
.
.
Place the dispenser on a suitable counter or stand.  
When the dispenser is in position for use, level the dispenser front to back as well as side to side by adjusting  
the legs.  
5
6
. Remove the cover.  
. Water connection:  
Water inlet is a 3/8 inch compression fitting on HWB-25, 1/4 inch compression fitting on all other models.  
The dispenser can be connected to a cold or hot water line. Cold water is preferred for best flavor, but hot  
water will allow for faster recovery times. Use of an in-line water filter is strongly recommended.  
Install a water shut off valve near the dispenser to facilitate service. If an in-line water filter is used, it should  
be installed after the water shut off valve and in a position to facilitate filter replacement.  
Flush the water supply line and filter before connecting it to the dispenser.  
Verify that the water line will provide at least 2 gallons per minute and that the water pressure is between 20  
and 75 psig.  
Use a wrench on the factory fitting when connecting the incoming water line. This will reduce stress on the  
internal connections and reduce the possibility of leaks developing after the installation has been completed.  
7
. Vent tube connection:  

In addition to the user manual Fetco Home Decor Water Dispenser HWB-2000, we also provide a support panel to help you solve your problems with Fetco Home Decor Water Dispenser HWB-2000. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Fetco Home Decor Water Dispenser HWB-2000. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Fetco Home Decor Water Dispenser HWB-2000 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.