If you found this page, you probably have a problem and you need a user manual for the device Wilton PF3-EZ. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Wilton PF3-EZ it belongs to the category Saw. A user manualWilton PF3-EZ is taken from the manufacturer, a Wilton company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Wilton PF3-EZ directly. You can view the user manualWilton PF3-EZ directly online or save and store it on your computer.

6

.

.

Tighten the screws firmly with a 19mm  

wrench.  

7

Insert the pin assembly into the hole (Figure  

2

). You may need to rotate it until it seats  

properly in the hole.  

8

.

.

Install a flat washer and cast iron handle  

(

Figure 2) to the threads of the top screw as  

shown, by screwing the handle down  

clockwise onto the screw threads.  

9

In the area above the pin, remove the hex  

nut from the screw with a 19mm wrench, but  

leave the flat washer in place. In place of  

the hex nut, install the cam handle (Figure  

Figure 2  

Figure 3  

Figure 4  

2

). Screw the cam handle clockwise onto  

the threads (the cam handle will contact the  

pin on each rotation and push the pin  

downward.) Tighten the cam handle.  

1

0. Loosen the hex nut (A, Figure 3) with a  

2mm wrench, and back off the set screw  

1

(

B, Figure 3) with a 4mm hex wrench, until  

the shaft of the handwheel can be inserted  

freely into the hole in the bracket (Figure 3).  

The handwheel should be positioned so that  

the pinion on its shaft is approximately  

centered with the keyway of the bracket.  

1

1. Turn the set screw (B, Figure 3) clockwise  

into the shaft just enough to prevent the  

handwheel from slipping out. Do not  

overtighten the set screw. Tighten the hex  

nut (A, Figure 3).  

12. Loosen the handle above the bracket  

(

Figure 4).  

1

3. The end of the horizontal arm that has the  

rack extending to the end will be inserted  

into the bracket. Insert the horizontal arm,  

with the rack pointed downward, into the  

bracket. The rack will fit through the keyway  

in the bracket. See Figure 4. Continue to  

push the horizontal arm into the bracket  

while slightly rotating the handwheel  

counterclockwise, until the rack and pinion  

mesh. The horizontal arm can now be  

moved into the bracket by rotating the  

handwheel.  

1

4. Install the elevating column onto the  

horizontal arm (Figure 5). Make sure the  

horizontal arm slides all the way into the  

sleeve of the elevating column (The end of  

the rack on the horizontal arm will almost  

touch the sleeve). Check that the elevating  

column assembly is in the vertical position.  

Tighten the two screws on the sleeve  

(

Figure 5) with a 19mm wrench.  

15. Install a flat washer and handle on the  

screw of the elevating column (Figure 5).  

Figure 5  

10  

• ← Previous
• Next page →

In addition to the user manual Wilton PF3-EZ, we also provide a support panel to help you solve your problems with Wilton PF3-EZ. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Wilton PF3-EZ. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Wilton PF3-EZ - you will surely help many users by doing so.