Manuel d'utilisation SECO-LARM USA Enforcer RF Receivers SK-910RL-4

Si vous arrivez à cette page, vous avez probablement un problème, et vous avez besoin de manuel du dispositif SECO-LARM USA Enforcer RF Receivers SK-910RL-4. Soyez sûr de vérifier qu'il s'agit exactement de manuel du dispositif que vous cherchez. Dans notre base de données SECO-LARM USA Enforcer RF Receivers SK-910RL-4 il appartient à la catégoriePoste stéréo. Le manuel d'utilisation SECO-LARM USA Enforcer RF Receivers SK-910RL-4 vient du fabricant, l'entreprise SECO-LARM USA - c'est un document officiel, et si vous avez des doutes quant à son contenu, s'il vous plaît contacter directement le fabricant SECO-LARM USA Enforcer RF Receivers SK-910RL-4. Le manuel SECO-LARM USA Enforcer RF Receivers SK-910RL-4 peut être visualisé directement en ligne, ou enregistré et stocké sur votre ordinateur.

System  
These RF receivers are compatible with both code hopping and fixed-code transmitters (see page 4 of this manual for  
a list of compatible transmitters). They can be used for a variety of applications, such as allowing the same transmitter to  
arm/disarm a vehicle alarm and open/close a garage door opener. The receivers come in one- or two-channel  
versions. Each channel can learn the codes of up to 15 different transmitter buttons on a first-in, first-out basis.  
Installation Notes  
1
. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or  
moisture. Metal will block the RF signal, resulting in a reduced range.  
2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives interference from  
local RF activity (eg., airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.  
Learning a New Button Code (channel 1)  
1
. Press mode switch #1 for three seconds. The green LED will start to flash quickly.  
2
. While the green LED is flashing quickly, press a button on a compatible transmitter. The green LED will flash once  
and then turn off to show that that button was learned.  
3. Repeat steps 1 and 2 to learn more buttons into channel 1.  
NOTE — The green LED will flash a maximum of 15 seconds. If no transmitter button is pressed during this time, the  
receiver will exit the code-learning mode, and the green LED will turn off.  
Learning a New Button Code (channel 2)  
The procedure is the same as for channel 1, except mode switch #2 initiates the code-learning process, and the red  
LED shows status.  
Note Regarding Code Learning  
1
2
3
. The receiver will only learn the code of a particular button once. Once a button’s code is learned, if you try to  
code-learn that button again, whether it is for the same channel or not, the receiver will exit code learning mode.  
. Each channel can learn the codes of a maximum of 15 transmitter buttons. If you attempt to learn a sixteenth  
button, the earliest code learned will be deleted.  
. To clear all codes — Press the appropriate mode switch (#1 or #2) for three seconds. When the LED starts  
flashing, press that switch again for three seconds. The LED flashes twice to indicate that all codes associated  
with that channel are now deleted.  
Programming Relay Output Modes  
The relay output(s) can be programmed for one of four different modes, depending on the application:  
4-second momentary — Press the transmitter button once. The relay turns on for 4 seconds, and then turns off.  
(This is the DEFAULT mode)  
1-second momentary — Press the transmitter button once. The relay turns on for 1 second, and then turns off.  
Toggle — Press the transmitter button once, and the relay turns on. Press a compatible transmitter button again,  
and the relay turns off.  
Latch — Press the transmitter button once, and the relay turns on and stays on. The relay will remain on until the  
appropriate mode switch (#1 or #2) is pressed to reset, regardless of whether a compatible transmitter button  
is pressed again or not.  
To program outputs, open case and find the 2 jumpers marked LP1 and LP2. Cut these jumpers, if needed, as follows:  
Output type  
LP1  
-second momentary Uncut  
-second momentary Uncut  
LP2  
4
Uncut  
Cut  
1
Toggle  
Latch  
Cut  
Cut  
Uncut  
Cut  
NOTE — On the 2-channel models, the output mode of both relays is the same. In other words, you cannot have 4-  
second momentary output for channel 1 and latch output for channel 2.  

En plus du manuel SECO-LARM USA Enforcer RF Receivers SK-910RL-4, nous fournissons également des panneaux d'assistance qui vous aideront à résoudre vos problèmes avec SECO-LARM USA Enforcer RF Receivers SK-910RL-4. Si vous avez des questions, vous pouvez les poser dans le formulaire ci-dessous. Les autres utilisateurs qui viennent ici, auront l'occasion de vous aider à résoudre votre problèmeSECO-LARM USA Enforcer RF Receivers SK-910RL-4.

Problème avec le dispositif? Posez une question, nos utilisateurs peuvent aider

Personne n'a ajouté commentaire pour ce dispositif/manuel.