Handleiding Linear XR-D

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Linear XR-D nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Linear XR-D behoort het tot de categorie Satelliet radio. De handleiding Linear XR-D is afkomstig van de fabrikant, het bedrijf Linear - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Linear XR-D. De handleiding Linear XR-D kunt u direct online bekijken of op te slaan op uw computer.

6
.
CONSTRUCT CABLE & CONNECT POWER  
7. ASCII DATA OUTPUT DETAILS  
8. MOUNT ANTENNA AND ROUTE CABLE  
TRANSMIT DATA (TD)  
DATA TERMINAL READY (DTR)  
SIGNAL GROUND (SIG GND)  
ANT-1A  
USE ANT-1A ANTENNA  
FOR SHORT RANGE (LESS  
THAN 1 MILE)  
APPLICATIONS  
+
12 VDC  
DATA OUTPUT PRODUCED WHEN PRESSING XR-D TEST BUTTON  
ANTENNA  
GROUND  
A 65432 0001 21A0HX  
XR-D SERIAL DATA OUTPUT STRING KEY  
CON-180A  
STRAIGHT  
CONNECTOR  
SIG GND  
DTR  
TD  
P SSSSSS CCCC BTARVXE  
+
12 VDC  
CON-180A + CON-90A  
ANGLE CONNECTOR  
GROUND  
P = PACKET TYPE CHARACTER (A OR B). XT TRANSMITTERS SEND FOUR ROUNDS  
OF DATA EACH ACTIVATION. PACKET TYPE "A" IS FIRST ROUND, PACKET TYPE "B"  
IS FOR THE NEXT THREE ROUNDS.  
WARNING  
THIS UNIT REQUIRES 12 VDC AT 1/2 AMP.  
THE NO-LOAD VOLTAGE OF THE SUPPLY  
MUST NOT EXCEED 17.5 VDC OR DAMAGE  
TO THE UNIT WILL OCCUR!  
S = FIVE-DIGIT DECIMAL NUMBER (00000 - 65535) THAT IS EQUAL TO THE BINARY  
CODE SET ON THE TRANSMITTER'S SYSTEM CODE SWITCHES "A" & "B" . SYSTEM  
CODE SWITCH "B", POSITION 8 IS THE LEAST SIGNIFICANT BINARY DIGIT, SWITCH  
"
A" POSITION 1 IS THE MOST SIGNIFICANT BINARY DIGIT.  
ROUTE WIRES THROUGH  
CASE STRAIN RELIEF  
BUSHING BEFORE  
C = FOUR BINARY DIGITS (0 OR 1) INDICATING TRANSMITTER CHANNEL  
ACTIVATED. 0=NO ALARM, 1=ALARM. ORDERED CH4, CH3, CH2, CH1.  
XR-D TO FEMALE DB-9 FOR COMPUTER CABLE  
CONNECTING TO TERMINALS  
SIG GND  
DTR  
PIN 5 (SIG GND)  
PIN 6 (DSR)  
PIN 2 (RD)  
B = ONE-DIGIT DECIMAL NUMBER (0 - 3) EQUAL TO THE BANK NUMBER (1-4) SET IN  
THE TRANSMITTER.  
USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER  
RANGE APPLICATIONS OR DIFFICULT  
INSTALLATIONS  
TD  
FEMALE  
DB-9  
+
12 VDC  
GROUND  
T = ONE-DIGIT DECIMAL NUMBER (0 - 2) DEFINING TRANSMITTER TYPE  
(
0 = XT-1, 1 = XT-4, 2 = XT-2H OR XT-4H IN MULTI-CHANNEL MODE).  
XR-D TO FEMALE DB-25 FOR COMPUTER CABLE  
A = ALARM/RESTORE CHARACTER (A OR R). RELEVANT FOR SINGLE-CHANNEL  
TRANSMITTERS ONLY.  
SIG GND  
DTR  
PIN 7 (SIG GND)  
PIN 6 (DSR)  
PIN 3 (RD)  
MOUNT ANTENNAS AS HIGH AS POSSIBLE  
(A METAL MOUNTING POLE IS RECOMMENDED)  
FEMALE  
DB-25  
TD  
+
12 VDC  
R = ONE-DIGIT BINARY DIGIT (0 OR 1) INDICATING THE STATE OF THE  
TRANSMITTER'S AUTO-RESTORE SWITCH (0 = OFF, 1 = ON).  
GROUND  
AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE  
ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.  
USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.  
V = TRANSMITTER VOLTAGE CHARACTER (H OR L). NORMAL CONDITION = "H". IF  
TRANSMITTER VOLTAGE IS BELOW 10.5 VDC CHARACTER = "L".  
XR-D TO MALE DB-25 FOR PRINTER CABLE  
SIG GND  
DTR  
PIN 7 (SIG GND)  
PIN 6 (DSR)  
PIN 3 (RD)  
MALE  
DB-25  
X = SPARE CHARACTER, NOT IMPLEMENTED AT THIS TIME.  
TD  
+
12 VDC  
E = END-OF-DATA. A CARRIAGE RETURN AND A LINE FEED ARE SENT.  
GROUND  
TO UNIT  
9
. TEST SYSTEM  
TRANSMITTER  
10. COMPLETE INSTALLATION  
LINEAR LIMITED WARRANTY  
This Linear product is warranted against defects in material and workmanship  
for twelve (12) months. The Warranty Expiration Date is labeled on the product.  
This warranty extends only to wholesale customers who buy direct from Linear or  
through Linear’s normal distribution channels. Linear does not warrant this product  
to consumers. Consumers should inquire from their selling dealer as to the nature of  
the dealer’s warranty, if any. There are no obligations or liabilities on the part of  
Linear LLC for consequential damages arising out of or in connection with use  
or performance of this product or other indirect damages with respect to loss of  
property, revenue, or profit, or cost of removal, installation, or reinstallation. All  
implied warranties, including implied warranties for merchantability and implied  
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the  
product. This Linear LLC Warranty is in lieu of all other warranties express or  
implied.  
INSTALL AND SETUP THE TRANSMITTER AS  
DESCRIBED IN ITS INSTALLATION INSTRUCTIONS  
APPLY POWER AND TRIGGER THE  
TRANSMITTER'S INPUT  
1
SECURE END PLATE BY  
INSTALLING THE FOUR  
CASE SCREWS  
INSTALL THE TWO REMAINING  
MOUNTING SCREWS  
THE TRANSMIT INDICATOR  
SHOULD LIGHT WHEN THE  
TRANSMITTER IS TRIGGERED  
2
SLIDE RECEIVER  
BOARD INTO CASE IN  
THE 3RD SLOT UP  
WARNING  
All products returned for warranty service require a Return Product Authorization  
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#  
and other important details.  
NEVER CONNECT THE TRANSMITTER AND  
RECEIVER ANTENNA CONNECTORS  
DIRECTLY TO EACH OTHER. MAJOR  
DAMAGE TO BOTH UNITS WILL OCCUR!  
VERIFY THAT COMPUTER OR PRINTER  
IS SETUP PROPERLY AND ACQUIRING  
THE DATA FROM THE RECEIVER  
IMPORTANT !!!  
(
BUTTON WILL ALSO SEND DATA)  
PRESSING THE RECEIVER'S TEST  
Linear radio controls provide a reliable communications link and fill an important need  
in portable wireless signaling. However, there are some limitations which must be  
observed.  
RECEIVER  
1
WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow  
unlicensed high-power transmissions at or near the operating frequency of this product which may  
interfere with, or even disable, normal operation of this radio device.  
3
BAUD RATE: 9600  
STOP BITS: 1  
PARITY: NONE  
1
1
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95  
Radio Control devices. As such, they have limited transmitter power and therefore limited range.  
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals  
that occur on or near their operating frequencies, regardless of code settings.  
Changes or modifications to the device may void FCC compliance and user’s authority to operate equipment.  
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.  
TIGHTEN WIRING STRAIN  
RELIEF BUSHING TO  
SECURE AND WEATHER  
PROOF WIRING  
1
1
SEND MORE TEST TRANSMISSIONS, THE  
RECEIVER'S SIGNAL INDICATOR SHOULD  
LIGHT AS THE SIGNALS ARE RECEIVED (IF  
LIT WITH NO SIGNALS, IT IS INTERFERENCE)  
TEST SYSTEM AGAIN AFTER  
COMPLETING INSTALLATION  
1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or  
dealer, and these facts should be communicated to the ultimate users.  
Copyright © 2004 Linear LLC  
215170 B  

Naast de handleiding Linear XR-D, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Linear XR-D. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Linear XR-D. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Linear XR-D - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.